Nerf N-Strike Elite Jolt Blaster

Product Information

Because of this blaster’s petite size modifying the blaster might prove to be difficult. When modifying blasters as small as the Nerf Jolt, you risk damaging the blaster and its internal workings. With only a little bit of work you have increased the power of your Nerf Jolt by 15 feet per second from its original firing power. It really is as simple as that!

Once the dart post is out, reach further down the barrel with a screwdriver (or pliers) and take out the air restrictor.While some Nerf blaster mods cover one aspect of the blaster at a time. However, if you are looking for a mod that will cover every aspect of your Nerf Jolt then this is the perfect mod for you! Crossfire Bow • Doublestrike • Fusefire • Jolt • Ricochet • Ripshot • Rough Cut 2x4 • SlingFire • Sidestrike Finding the correct size of sealing ring for your Nerf Jolt might prove to be rather difficult; however, creating another layer of seal with the electrical tape is effective, easy to do, and not as costly.

However, because of this blaster’s smaller size and the challenges the Nerf Jolt poses in modifications it is very popular for Nerfer’s to try to conquer the Nerf Jolt by creating successful mods. Surprisingly, second place for the range assessment was given to the Nerf Rival Roundhouse XX-1500 Blaster— the model that uses foam balls as a projectile rather than darts. The furthest ball we recorded traveled a distance of 88 feet. It's even more impressive that this is a manually powered toy blaster that is not that hard to set. The Roundhouse gets the thumbs up from the GearLab crew. To start this method of making the SuperJolt, all you need to do is grab the dart post with your pliers and twist! The dart post should break off fairly easily. Next, you take your screwdriver and place the tip of it down the barrel against the air restrictor. Break the air restrictor off with a few good taps and shake any extra pieces out of the barrel. The majority of the blaster is one solid piece of plastic, rather than two separate halves attached together with screws or tabs. The only separate pieces are the trigger mechanisms, the plunger, and a plate from which the plunger rod projects from. The simplest method for this mod takes only a matter of minutes and only requires a screwdriver and some needle nose pliers.You can further increase the power of your blaster by doing a simple spring upgrade in the piston. Get your Nerf Jolt Spring Upgrade here!

To ensure no pieces are lost from the base plate fling off, remove the last screw slowly while applying pressure to the base. Once the screw is removed slowly decrease the pressure until the plunger system is no longer pushing against the base plate. Tactical Jolt Alpha Trooper CS-12 • Firestrike • RapidStrike CS-18 • Rayven CS-18 • Rayven Stinger • Rough Cut 2x4 • Spectre REV-5 • Strongarm • Stryfe • Triad EX-3

Why You Should Trust Us

Feeling brave enough to take on modding your Nerf Jolt? Keep reading to find the best mods and how to do one for yourself! Due to the simplistic nature of the Jolt, there is little room for modifications. Because of this, as well as its size, it can be a good candidate for blaster integrations. Alpha Trooper CS-18 • Barrel Break IX-2 • Barricade RV-10 • Deploy CS-6 • LongStrike CS-6 • Rapid Fire AS-20 • Spectre REV-5 • Stampede ECS While there are plenty of do it yourself Nerf Mods, Nerf also sells its own attachments to improve the performance of their blasters. With tons of attachments to choose from, you may not know which ones will best benefit your blaster. To give your Nerf Jolt more power you will need to seal off the plunger. This can be done by removing the plunger system and either adding a thin layer of electrical tape under the current sealing ring or by purchasing a heavier duty sealing ring.