Nartel® 10 X 1 AMP SHAVER FUSES BS646 1AMP MINI FUSE 20MM X 5MM

Product Information

Once this is done, a minor works certificate is then issued to prove the installation has been carried out correctly. Once all the wires have been connected, the face plate is then screwed on to the pattress box, fixing it in place. In this example here we are using an existing lighting circuit so a 1mm twin and earth cable is run out from the top of the ceiling rose, down through the ceiling and down a chase that was cut into the wall. Hard to see how that's true, as shaver plugs and standard 2-pin continental mains plugs have different spacing. Yes you can force them in but I'd not agree that makes it "suitable". As previously mentioned, if you are sing a lighting circuit make sure it’s RCD protected. If it isn’t then you can’t use it.

Nartel® 10 X 1 AMP SHAVER FUSES BS646 1AMP MINI FUSE 20MM X 5MM

shaver adaptors: (e.g. http://www.maplin.co.uk/Module.aspx?ModuleNo=1186&DOY=31m3#features) theese are designed for shavers and can also be used for other very small <1A appliances that do not require earthing and come with a two pin europlug (a relatively thin plug with two thin flexible pins). They are NOT suitable for either applicances that require higher currents or those that require earthingZone 0 – the interior of the bath or shower which can hold water. No appliances should be installed here period!

Shaver Plug Adaptor, UK 2 Pin to 3 Pin 13A Fuse LENCENT Shaver Plug Adaptor, UK 2 Pin to 3 Pin 13A Fuse

Ideally look for a model with double wound isolating transformer, integral overload protection and shutters on the plug inlets to prevent any accidental splashing. Using electrical equipment in bath or shower rooms has always needed great care to ensure safety due to the obvious risks of mixing water and electricity. However if you are installing in an upstairs then you may be able to locate a suitable supply in the loft. This is often the easiest route as everything should be much more accessible. Once a suitable supply has been found the next task is to isolate the supply to the circuit you are using! If in any doubt, the power to the entire house is turned off. Suitable for accepting the plugs fitted to electric shavers and standard 2-pin continental mains plugs"

Where can I Install a Shaver Socket in a Bathroom?

Unfortunately most stores only carry the first two categories and often provide poor information about what they are suitable for The cable was then secured in place using UPVC capping to not only hold it but also protect it from any damage that might from any potential future work. Once in place the cable was then tested to ensure there were no breaks etc. This is a necessary step as once the cable is filled over it’s a nightmare to have to dig it all out if it’s damaged.

Masterplug 3-Pin Fused Shaver Adaptor - Screwfix

As we have mentioned above, when running down a wall to a power supply unit such as this the cable will need to run vertically down in a straight line to comply with regulations.

Different Types of Shaver Socket

There are many types of adaptors on the market and knowing what is suitable for what purpose is important to get a safe and reliable result.

Wilko 1 Amp Fused Shaver Adaptor | Wilko - Wilko Site Wilko 1 Amp Fused Shaver Adaptor | Wilko - Wilko Site

Plugwash's final suggestion is the one to go for - just change the plugs on your appliances and have done with it. visitor adaptors (e.g. http://www.roamingfox.co.uk/UK-Visitor-Travel-Adapter-pr-16228.html ). Theese have a higher current rating than shaver adaptors and can be used with some earthed plug types. However THEY WILL NOT PROVIDE AN EARTH TO GERMAN/DUTCH/FRENCH plugs. No, I meant my own european shaver has a plug similar to the standard 2 pin thin plug which is in use with some non-earth products. By the way, do you have any comment on my message to Plugwash? Thanks!

🍪 About Cookies on our Site

The cable is then normally capped (covered with a protective UPVC capping) or run through some UPVC trunking/pipe to protect it and hold it in place. Below is another example of the same plug I bought (I bought the same type at ASDA) and it has a plastic grounding with a 1 Amp fuse. In both cases, the cables are run down through the ceiling and down a chase cut into the wall to run to both locations Wall chased out and cable placed in chase and protective UPVC pipe Step 3 – Install Fused Connection Unit (FCU)