OMPHOBBY M1 RC Helicopter for Adults, Dual Brushless Motors Mini Helicopters Direct-Drive 3D Remote Control Aircraft-BNF (OMP Protocol Purple)

Product Information

The OMPHobby M1 is compatible with the Radiomaster 4in1 series of radios (Both Types - OMPHobby Protocol & SFHSS) Included accessories: Charge lead, nut wrench, screwdriver, 1mm hex wrench, spare screws & servo arms. The OMPHobby M1 RC Helicopter is the original high quality RC helicopter with 290mm blade diameter weighing in at only 118g. The M1 features dual brushless motors along side a powerful onboard flight controller that supports three flight modes - altitude stabilisation, soft 3D and aggressive 3D. The OMPHobby M1 RC Helicopter is a great micro (150 size) 3D Flybarless RC helicopter. Best for indoor flying during bad weather days. It can be flown outside as well.

M1 is a high-quality product developed by OMPHOBBY for helicopter enthusiasts. Its compact size makes it flexible for either indoor flight or outdoor violent flight. SFHSS/DSM/OMP: Removed PCs curve from pitch mix so pitch doesn't change when switching to stability mode. Usage Warning:Please note that this is not a toy and should not be used by a child without suitable adult supervision due to the high speed prop which might cause injury. The product includes a LiPo battery which will require safe handling/charging and should be regularly topped up when the model is not in use. ** The helicopter supports one Spektrum DSM Satellite port. You can connect a Spektrum satellite receiver to this port. e.g. DSM2 / DSMX nano Satellite receiver with bind button.

Required accessories (not included)

For OMP Protocol, there are no throttle curves on the Radio Transmitter as throttle curve is fixed inside the Helicopter. For other protocols, the below curves are used. Curve The OMPHobby M1 EVO RC Helicopter is the latest revision of the M1 helicopter. It has an updated carbon fibre frame and available in 4 new colours. OMPHobby M2 EVO and M1 EVO OMP comes with built-in receiver that supports OMP Protocol. In OMP Protocol, the throttle curve is fixed in the helicopter and cannot be adjusted at the Transmitter Radio. OMP protocl supports telemetry for Helicopter battery voltage. Normal, Idle-up1 and Idle-up2 flight modes are assigned by a switch on the Radio transmitter.

FUT/DSM: Change normal mode throttle curve to 0,5,5,5,5. We want governor to be engaged throughout except full negative. Flight time: the maximum flight time is 8 minutes at ~ 50% throttle and 4 minutes at ~ 90% throttle. For OMP Protocol, there are no pitch curves on the Radio Transmitter as pitch curves are fixed inside the Helicopter. For other protocols, the below curves are used. CurveThis is a “bind and fly” helicopter kit which requires a separate compatible radio transmitter of your choice. The Radiomaster ZORRO RC Transmitter (4 in 1) comes programmed for use with the M1 RC Helicopter. The onboard flight controller has a built in Futaba Protocol (SFHSS) receiver for use straight out of the box with a Futaba / Radiomaster TX16S, Zorro etc. SFHSS transmitter. For other brands you can also use a SPEKTRUM / DSMX transmitter and receiver (adapter cable sold here), FrSky, etc. transmitter and receiver via S.BUS port (adapter cable sold here). Note that R-XSR receiver supports 2 modes on SBUS out pin (SBUS mode and CPPM mode). This pin should be in SBUS mode to work with M1/M2 helicopter. The blue LED is turned ON for SBUS mode and OFF for CPPM mode. Press the bind button for 4 seconds to switch between the two modes. It is a good idea to remove the main and tail blades of the helicopter to prevent any injury if motors start accidentally. The Archer Plus RS mini receiver is perfect for M1 and M2 helicopters due to its compact size. It even comes with the correct adapter cable.