Joined in 2023 
82 
63 About this deal
Why cannot I access the Internet after successfully connected to the TP-Link router’s wireless network(Windows OS)? 09-06-2019 1551544 Microsoft® Windows® 98SE, NT, 2000, XP, Vista™ or Windows 7, 10, MAC® OS, NetWare®, UNIX® or Linux. To get a reliable serial connection, you might have to connect a 10k pullup resistor between TX and VCC. This is because the TX pin is connected to a voltage divider (2×5.6k) and a capacitor is put between the real pin and the TX connector. Some serial adaptors might work without the pullup resistor (confirmed for one ST3232-based adaptor), but others definitely require it (confirmed for a FTDI FT232RL-based model).
How to set up Port forwarding feature on my TP-Link Wireless Router for Xbox Live? 07-01-2020 290911 Some official firmware of TP-Link products can be replaced by the third party firmware such as DD-WRT. TP-Link is not obligated to provide any maintenance or support for it, and does not guarantee the performance and stability of third party firmware. Damage to the product as a result of using third party firmware will void the product's warranty. Open Source Code For Programmers (GPL) To avoid wireless disconnect issue during firmware upgrade process, it's recommended to upload firmware with wired connection unless there is no LAN/Ethernet port on your TP-Link device. DONT DO ANYTHING. Just wait and router reboot itself. wait few minutes and you will able to reach Luci via 192.168.1.1.
Important Notice
How to confirm whether the router is connected to internet through Diagnostic function 06-29-2022 311610
Please verify the hardware version of your device for the firmware version. Wrong firmware upgrade may damage your device and void the warranty. ( Normally Vx.0=Vx.6/Vx.8 (eg:V1.0=V1.6/V1.8); Vx.x0=Vx.x6/Vx.x8 (eg:V1.20=V1.26/V1.28) A firmware update can resolve issues that the previous firmware version may have and improve its current performance. To Upgrade Why cannot I access the Internet after successfully connected to the TP-Link router's wireless network(MAC OS)? 04-17-2019 503744 Microsoft® Windows® 98SE, NT, 2000, XP, Vista™ of Windows 7, 10, MAC® OS, NetWare®, UNIX® of Linux. Wireless setup completed now we need to get ip WAN interface via main router dhcp server. Set your network config like below example.Downgraded wrong image ( jff2 instead of squashfs ) cause cant get ip or connect to luci. Failsafe mode still working but firstboot command wont work because it is already on working. You can upload correct firmware and write it with mtd command but failsafe mode can't connect internet. You need to local tftp server to get firmware. The difference is rather small and probably due to soldering and possibly quality of analogue components on the PCB. Noise level is rather constant between the two tests though.
The txpower sweetspot is therefor estimated to be 1000-1200. This would equal a signal strength of 2-4dBm (1.5-2.5mW). To max that up to the common legal maximum of 100mW ERP you'll need an 18-21dBi antenna. You'll be much better of with a clean signal and a high gain antenna than attempting to crank up the signal strength to a level where it only cripple the signal with distortion. How to solve the compatibility problem between your 3G modem and TP-Link 3G router 06-10-2021 109810 How to share local resources on the Internet by Virtual Servers on TL-MR3020 (Router mode--new logo) 06-27-2022 35510Notice the amount of distortion outside of the 20MHz signal at 1800 compared to 1200 or 900. It is hard to say how much of this distortion is also available in the 20MHz signal, my guess is at least as much. This cripples the signal, making a greater txpower probably a worse signal with less speed than one without the distortion. Memory: 29864k/32768k available (1889k kernel code, 2904k reserved, 524k data, 116k init, 0k highmem) Test your router: If your router is properly connected to the internet you should get something like the below lines: Kernel command line: console=ttyS0,115200 root=31:02 rootfstype=squashfs init=/sbin/init mtdparts=ar7240-nor0:128k(u-boot),1024k(kernel),2816(rootfs),64k(config),64k(ART) mem=32M What should I do if I fail to log into MR3020’s management interface when it works in RE or WISP mode? 01-31-2018 40492
To install OpenWrt from the U-Boot console, you need to install a TFTP server on your computer ( tftp-hpa is recommended). Is is very evident that the greater txpower, the greater amount of noise and distortion in the signal. The signal is very clear around txpower 800, while rather terrible when set to 1800 and more. If you install openwrt from trunk, the firmware image doesn't include LuCi. You need configure wireless network from telnet to install Luci. You will need already working internet access. IMPORTANT: To prevent upgrade failures, please read the following before proceeding with the upgrade process Start your terminal and connect 192.168.1.1 via telnet ( port 23 ). Right now LAN INTERFACE include wireless too. We need to set wireless to WAN interface. Change wireless configuration below example.
Firmware
Do NOT turn off the power during the upgrade process, as it may cause permanent damage to the product.
Great Deal 
New Comment