FireAngel FA3313 Carbon Monoxide Detector and Alarm with 1 Year Replaceable Batteries (Replacement for FireAngel CO-9B)

Product Information

The advice below is purely provided for ‘best practice’ and should not be used independently. Please note, these alarms are not suitable for homes in Scotland under the new Fire & CO regulations. For alarms located in the same room as a fuel-burning appliance (for both wall and ceiling mounted alarms) the following applies: FireAngel’s FA3322 digital carbon monoxide alarm features many icons on the LCD screen. View our guide below to help you understand what each represents. All alarms are calibrated and rigorously tested in-house and are third party tested to receive the BSI Kitemark certification to provide peace of mind. Also, the new range is compliant with the revised European Standard EN 50291-1:2018 to ensure maximum protection. FA3322X4: Carbon Monoxide Alarm with digital display and 10 year battery Find out more about the FA3313X4 CO Alarm. FA6813-EU: Carbon Monoxide Alarm with replaceable batteries

Find out more about what you should expect from your landlord for CO safety in your home. Get protected today With our sleep easy function, you can silence low battery chirps for 8 hours, up to 10 times. This feature not only allows you to enjoy a silent night’s sleep, but gives you vital time to take action and replace your batteries.We recommend you clean your smoke and heat alarms every 3 months to stop a build-up of dust or insect webs from preventing the sensor to work correctly.

Looking for a CO-9D alarm replacement? FireAngel’s new FA3322X4 alarm will be replacing any end-of-life CO-9D alarms. An audible Carbon Monoxide detector is the only way to be alerted to a carbon monoxide leak; it can’t be smelt, tasted or seen so it’s impossible for human senses to detect. Ideally, an alarm should be installed in every room containing a fuel-burning appliance and every sleeping room. Additional alarms may be installed to ensure that adequate warning is given for occupants in other rooms, in which they spend considerable time whilst awake and from which they may not be able to hear an alarm in another part of the property. Using a soft brush adaptor, your vacuum or your hairdryer on a cool setting, run along the edges and face of the alarm. Please do not use any solvents or cleaners on your alarm as they may cause damage to the sensor or circuitry. I completed everything that you advised by cleaning any dust on the alarm and banging in the palm of my hand to dislodge anything.Experience both audible and visual safety warnings with the digital screen, which will change colour to indicate different incident types for clear safety advice. Find out more about the FA3820X4 CO Alarm. FA3313X4: Carbon Monoxide Alarm with replaceable batteries However, if you notice any visible damage to the alarm during cleaning, including any severe staining or dust, we recommend you replace the alarm as the sensor within could be damaged. Does cleaning my alarm really help stop the beeping? With low level CO monitoring, a pre-alarm warning to open windows helps reduce the risk of CO poisoning and prevents build-up of dangerous CO levels. If a room is not ventilated and ppm levels continue to increase, the alarm will activate. We do not recommend a smoke alarm to be fitted in areas where excessive dust or dirt could contaminate the sensing chamber, making it over sensitive. It is also not advised to fit alarms in bathrooms, shower rooms or any other very damp and humid areas, where moisture can cause unwanted alarms.

Under the extended Smoke and Carbon Monoxide Alarm (England) Regulations 2015, from October 1st 2022, a carbon monoxide alarm will be required in all rooms where there is a fixed combustion appliance – such as gas boilers or gas fires – once the compliance date is announced. However, gas cookers are excluded from the updated regulation. If your alarm is not a sealed battery alarm, then install the batteries following the steps within the manual. Remove the disabling clip by pulling it out of the alarm and retain the disabling tab for future use. A common cause of nuisance alarms is the incorrect positioning of a smoke or heat alarm. If your FireAngel alarm has begun chirping not long after installation, make sure it is fitted in the right room in your home.Free-standing installation: The base of the alarm has been designed to allow it to stand freely on a shelf where required. These alarms fall under the Waste Electrical and Electronic Equipment regulations (WEEE). The directive requires producers of Electronic Equipment to join a WEEE compliance scheme and contribute to the cost of recycling Waste Electronic Equipment that is collected at local recycling centres and other routes. FireAngel smoke, heat and carbon monoxide (CO) alarms are designed to be as maintenance-free as possible, however there are a few steps that must be followed to ensure your alarms continue to perform correctly.

With the alarm memory function, the red LED will flash to provide a visual indication of a previous CO alarm activation. Once your CO alarm is activated and tested, choose to install the alarm by mounting on a wall or free standing on a shelf. Your alarm should be placed 1-3 metres away from any fuel burning appliance in your home, in living rooms or bedrooms. The FA6813-EU offers electrochemical sensing technology and a clear loud alarm to ensure trusted carbon monoxide (CO) detection for your home. This alarm also features our new Crescendo Test, which helps to protect your hearing by allowing you to choose the volume level of the test alarm. Simply hold down the test button and the alarm will move through the increasing volume levels (similar to a rising ‘crescendo’) until you find the alert sound level you are comfortable with. Alarms located in sleeping rooms and in rooms without a fuel-burning appliance should be located relatively close to the breathing zone of the occupants. The alarm’s high sensitivity mode will be enabled if the alarm predicts CO levels will increase to or above 180ppm for fast reaction to rising CO levels.https://www.fireangel.co.uk/wp-content/uploads/2022/10/MA0394R1-FireAngel-CO-Icon-Guide-Blog-Assets-Identifier-Guide-Draft-1_Power-Nightime-Sensing.mp4 We have been monitoring it since and I’m pleased to say that the issue appears to have been resolved so no requirement to issue a replacement. WARNING: This alarm will only indicate the presence of carbon monoxide gas at the sensor. Carbon monoxide gas may be present in other areas. Where should I position the CO alarm? The FA3313X4 is the ideal replacement for end-of-life FireAngel CO-9B alarms, featuring the highest level of CO detection for your home. With intelligent CO sensing technology and built-in features including Sleep Easy function and Alarm Memory, this alarm will keep your family protected from carbon monoxide. Read our handy guide for more information on correctly installing your alarms or discover why your Pro Connected alarms may be beeping in our guide. Dust contamination: How do I clean my alarm?