Teensy 3.6 (Without Pins)

Product Information

Teensyduino 1.58 supports Arduino versions 1.8.5 and 1.8.9 and 1.8.13 and 1.8.15 and 1.8.16 and 1.8.19. All of this functionality is jammed into a 62.3mm x 18mm board with all headers on a 0.1" grid so you can slap it on a breadboard and get to work! The Teensy 3.6 (as well as its sibling, the Teensy 3.5) is larger, faster and capable of more complex projects, especially with its onboard microSD card port. An upgraded ARM Cortex MCU (180MHz from 72MHz), more memory (1M from 256K)---as well as more RAM, EEPROM and accessible pins---make up the key new features of this board. The Teensy 3.6 is slightly scaled up from the Teensy 3.5. delay(), delayMicroseconds(), delayNanoseconds() - Simple delay for milliseconds, microseconds, or nanoseconds. These special functions and their respective pins are illustrated in the Teensy 3.6 pin diagram shown above.

In 2016 the 3.5 and 3.6 Teensy boards were released after another crowdfunding effort, of the 3.5 and 3.6 Teensy boards. These are the most powerful boards produced by the company up to date. analogWriteFrequency function. Slew Rate Limiting This optional feature greatly reduces high frequency noise when Teensy 4.0: Primary XBAR Pins 1, 2, 3, 4, 5, 7, 8, 30, 31, 32, 33 - Alt Pins: 0, 34, 35, 36, 37, 38, 39

Added partial SoftwareSerial for Teensy 3.0. If the pins match one of the real serial ports, hardware serial is used. This allows use of libraries that are hard-coded for SoftwareSerial. If non-serial pins are specified, only transmit works. Software-based receive is not yet supported (but planned for a future release)

Teensy 3.1 adds several new features, due to an upgraded microcontroller. Here are the highlights. A Libraries ported to Teensy 3.x: AltSoftSerial, CapacitiveSensor, FlexiTimer2, FreqCount, FreqMeasure, FrequencyTimer2, MsTimer2, ShiftPWM, TimerOne, TimerThree, Tlc5940 in boards.txt. Beware that on older versions of Teensyduino, these changes should be made directly to platform.txt. While a variety of MicroMod Carrier and Function boards are available within the MicroMod ecosystem, those looking to take full advantage of the Teensy Processor during their investigation and prototyping efforts should consider pairing it with the SparkFun MicroMod ATP Carrier Board, as many of the pins with extra functionality may be tied to a specific use on other Carrier Boards. AGND pin is meant only for the grounds from sensitive analog signals. Power Consumption (info here) Low Power Features (info here - Snooze library) VBAT A 3 volt coin cell may be connected to VBAT & GND to allow theSimilarly, the maximum size of the delay lines of some reverb algorithms might be too big and should be adjusted. Using the -dlt option can help, see the Managing DSP Memory Size section. The pin assignments have been designed to preserve compatibility with the 28 breadboard-friendly pins of prior Teensy 3.x models. All 28 of these pins support the same features as the older models.

Adafruit's Ethernet.init(CSPIN) extension is supported, to allow use of different pins for the chip select signal. Optimized direct register I/O is used for most Arduino compatible boards. from flash memory. Digital Signal Processing DSP extension instructions accelerate signal processing, Since the built-in LED is on pin 13, just like the Arduino, the basic blink sketch will work on the Teensy 3.6. The code is shown below.

Windows Installation

Processor Performance (info here) Floating Point Unit The FPU performs 32 bit float math in hardware, at approximately the The corresponding Teensy Audio Library object can be generated by running: faust2teensy -lib FaustZita.dsp The processor on the Teensy also has access to the USB and can emulate any kind of USB device you need it to be, making it great for USB-MIDI and other HID projects. The 32-bit, 180MHz processor brings a few other features to the table as well, such as multiple channels of Direct Memory Access, several high-resolution ADCs and even an I2S digital audio interface! There are also four separate interval timers plus a delay timer! Oh yeah, and all digital pins have interrupt capability and are 3.3V tolerant.