276°
Posted 20 hours ago

OX Speedskim Semi Flexible Plastering Rule - ST 900mm

£29.1£58.20Clearance
ZTS2023's avatar
Shared by
ZTS2023
Joined in 2023
82
63

About this deal

Always add the plaster mix to the water, not the other way around. If you add water to the plaster, you will have to apply pressure to mix the plaster at the bottom of the pail and you will over-mix the plaster and it will set too fast to work with. Stir the mixture as you add in the plaster. Start with plaster tape to cover the joints, and then use scissors to make sure the edges are neat as possible. You do not want any excessive material here, as it will interfere with the process. Dirty walls are a major no-no for anyone who is going to plaster walls. Ensure that your wall is clean as possible by removing any dirt and debris; while also removing any loose plaster or wallpaper. To test whether the wall is ready to accept new plaster, run your finger over the surface. If it comes away caked with dust, it still needs some work. Spraying the wall with water will help the new plaster to adhere to the old wall. Plastering is a job which many people usually leave to the experts. But by preparing well and carefully following a practised method, it’s perfectly possible for you to plaster a wall. The finished result will be a nice smooth wall which is ready to accept paint or wallpaper. What do I need to plaster a wall?

In the 6 stages of plastering, each one plays an important part in getting good results at the end. So we’ve put together a handy guide which will talk you through them step by step. This is where you remove any ridges in the plaster by using firm pressure with your trowel. If the plaster is quite firm and not easy to push around you can widen the angle of your trowel against the wall, but be careful not to scrape the plaster off.A good quality paint brush - this is essential for keeping your edges clean and applying water to your plaster.

Once your guides have been extended then you can fill in the middle of the wall and the top section as before. If you’re looking to try your hand at a spot of DIY plastering for the first time, then chances are you’ll also want the sort of smooth finish that the professionals get. After all, the last thing you want is to end up with an uneven wall that’s going to wind you up whenever you see it. The final part of the six stages of plastering should leave you with a nice even slightly polished surface. It begins when the plaster starts to darken as it dries. This is where you can run the trowel with a firm pressure over the entire wall to finish. And you’re done! A plasterer’s hawk board - this is the tool that holds your plaster. A plastic hawk board is lighter than a wooden one, although both types are absolutely fine. A wooden hawk board will last much longer though. Most importantly, remember the plaster must be completely dry before you paint or wallpaper.See our guide for how to paint on new plaster.Start by clearing everything out of the room — furniture included. Also, depending on the wall you are plastering, some might need to disassemble any curtain rails or even take off radiators (or cover them at the very least).

Allow the first coat to dry for roughly 20-minutes and not a minute longer. During which time, use a trowel to get rid of unevenness; spraying the plaster with water only if necessary, so it's easier to smooth out later. Begin by putting some plaster onto the hawk board. Working from the lower-left center of the wall, use the plastering trowel to apply a small amount of plaster each time directly to the wall. Ensure you are holding the trowel at a 45º angle as you begin to work on an upward sweep. Flatten the trowel at the end of each stroke, and making sure you do not press the trowel flat against the wall either.keep 90% of your straight edge on what is already ruled flat - this will cut any excess off your newly applied plaster, so that is becomes flat and in line with the previous section. If the previously painted wall is in good condition, then yes, it is possible. However, this process might require you to wire-brush the surface with detergent and then follow up with a bonding product. To see what your wall may (or may not) require we recommend testing out a small area to be sure. Is plaster stronger than drywall? There is an art to plastering and a lot to be said for following the right steps to getting that perfect finish, so no cutting corners here! Plaster is stronger than drywall in the sense that if it's applied to the wall correctly, the product is not only harder but more durable than drywall. In addition, it's also a better sound insulator, more flexible, and results in a higher-end finish.

As the plaster begins to firm up this is when you can flatten off the first coat with a clean trowel, making sure that the bulges are pushed out. The secret to this (as with the majority of plastering) is to use firm pressure as you move your trowel across the wall in long movements, holding the leading edge of the trowel at about 10-15mm away. Yes, it is relatively easy to skim a wall in hopes of giving it an even finish. In this case, using one coat plaster is much easier than using the gypsum plaster that professionals call upon.

Asda Great Deal

Free UK shipping. 15 day free returns.
Community Updates
*So you can easily identify outgoing links on our site, we've marked them with an "*" symbol. Links on our site are monetised, but this never affects which deals get posted. Find more info in our FAQs and About Us page.
New Comment